Energy harvesting technologies have been explored by researchers for more than two decades as an alternative to conventional power sources (e.g. batteries) for small-sized and low-power electronic devices. The limited life-time and necessity for periodic recharging or replacement of batteries has been a consistent issue in portable, remote, and implantable devices. Ambient energy can usually be found in the form of solar energy, thermal energy, and vibration energy. Amongst these energy sources, vibration energy presents a persistent presence in nature and manmade structures. Various materials and transduction mechanisms have the ability to convert vibratory energy to useful electrical energy, such as piezoelectric, electromagnetic, and electrostatic generators. Piezoelectric transducers, with their inherent electromechanical coupling and high power density compared to electromagnetic and electrostatic transducers, have been widely explored to generate power from vibration energy sources. A topical review of piezoelectric energy harvesting methods was carried out and published in this journal by the authors in 2007. Since 2007, countless researchers have introduced novel materials, transduction mechanisms, electrical circuits, and analytical models to improve various aspects of piezoelectric energy harvesting devices. Additionally, many researchers have also reported novel applications of piezoelectric energy harvesting technology in the past decade. While the body of literature in the field of piezoelectric energy harvesting has grown significantly since 2007, this paper presents an update to the authors' previous review paper by summarizing the notable developments in the field of piezoelectric energy harvesting through the past decade.
Purpose-led Publishing is a coalition of three not-for-profit publishers in the field of physical sciences: AIP Publishing, the American Physical Society and IOP Publishing.
Together, as publishers that will always put purpose above profit, we have defined a set of industry standards that underpin high-quality, ethical scholarly communications.
We are proudly declaring that science is our only shareholder.
ISSN: 1361-665X
Smart Materials and Structures is a multi-disciplinary journal dedicated to technical advances in (and applications of) smart materials, systems and structures; including intelligent systems, sensing and actuation, adaptive structures, and active control.
Open all abstracts, in this tab
Mohsen Safaei et al 2019 Smart Mater. Struct. 28 113001
Elinor Barnett et al 2024 Smart Mater. Struct. 33 065010
Despite bone screws being the most commonly inserted implant in orthopaedic surgery, 10% of fracture fixation failure is a result of screw migration or pullout. In this study, the effect of four auxetic structures on the pullout performance of a novel unthreaded bone fastener was investigated through experiments and numerical simulations. The auxetic fasteners included the re-entrant, rotating squares, missing rib, and tetrachiral structures. Parametric CAD models were developed for each, and polymer samples manufactured using a stereolithography process. Pullout testing using bone analogue material found the rotating squares fastener to achieve superior pullout resistance 2.5 times that of the non-auxetic control sample. With a pullout to push-in force ratio of 33.7, this fastener achieved high pullout resistance with a low insertion force improving ease of installation. The Poisson's ratio of the structure was determined using image analysis to be −1.31, similar to the missing rib and re-entrant types. The low axial stiffness of 12.1 N mm−1 for the rotating squares fastener was the reason for superior performance, allowing axial and resulting transverse strain to be initiated at relatively low load. The effect of increased diametral interference was investigated, and the re-entrant structure found to be superior with pullout resistance improved by 342%. This work provides a foundation for further development of unthreaded auxetic bone fasteners, which have the potential to replace screws for some orthopaedic applications and significantly reduce the prevalence of pullout as a failure mode.
Amir Pagoli et al 2022 Smart Mater. Struct. 31 013001
Soft actuators can be classified into five categories: tendon-driven actuators, electroactive polymers, shape-memory materials, soft fluidic actuators (SFAs), and hybrid actuators. The characteristics and potential challenges of each class are explained at the beginning of this review. Furthermore, recent advances especially focusing on SFAs are illustrated. There are already some impressive SFA designs to be found in the literature, constituting a fundamental basis for design and inspiration. The goal of this review is to address the latest innovative designs for SFAs and their challenges and improvements with respect to previous generations, and to help researchers to select appropriate materials for their application. We suggest seven influential designs: pneumatic artificial muscle, PneuNet, continuum arm, universal granular gripper, origami soft structure, vacuum-actuated muscle-inspired pneumatic, and hydraulically amplified self-healing electrostatic. The hybrid design of SFAs for improved functionality and shape controllability is also considered. Modeling SFAs, based on previous research, can be classified into three main groups: analytical methods, numerical methods, and model-free methods. We demonstrate the latest advances and potential challenges in each category. Regarding the fact that the performance of soft actuators is dependent on material selection, we then focus on the behaviors and mechanical properties of the various types of silicone that can be found in the SFA literature. For a better comparison of the different constitutive models of silicone materials proposed and tested in the literature, ABAQUS software is here employed to generate the engineering and true strain-stress data from the constitutive models, and compare them with standard uniaxial tensile test data based on ASTM412. Although the figures presented show that in a small range of stress–strain data, most of these models can predict the material model acceptably, few of them predict it accurately for large strain-stress values. Sensor technology integrated into SFAs is also being developed, and has the potential to increase controllability and observability by detecting a wide variety of data such as curvature, tactile contacts, produced force, and pressure values.
Daniel Haid et al 2023 Smart Mater. Struct. 32 113001
Sports concussions are a public health concern. Improving helmet performance to reduce concussion risk is a key part of the research and development community response. Direct and oblique head impacts with compliant surfaces that cause long-duration moderate or high linear and rotational accelerations are associated with a high rate of clinical diagnoses of concussion. As engineered structures with unusual combinations of properties, mechanical metamaterials are being applied to sports helmets, with the goal of improving impact performance and reducing brain injury risk. Replacing established helmet material (i.e. foam) selection with a metamaterial design approach (structuring material to obtain desired properties) allows the development of near-optimal properties. Objective functions based on an up-to-date understanding of concussion, and helmet testing that is representative of actual sporting collisions and falls, could be applied to topology optimisation regimes, when designing mechanical metamaterials for helmets. Such regimes balance computational efficiency with predictive accuracy, both of which could be improved under high strains and strain rates to allow helmet modifications as knowledge of concussion develops. Researchers could also share mechanical metamaterial data, topologies, and computational models in open, homogenised repositories, to improve the efficiency of their development.
Parham Mostofizadeh et al 2024 Smart Mater. Struct. 33 065001
In this paper, surface conductive heating was utilized to actively control the stiffness of lattice metamaterials manufactured employing multi-material 3D printing. To create an electrical surface conduction, additively manufactured samples in single and dual material configurations were dip coated in a solution of carbon black in water. Electro-thermo-mechanical tests conducted successfully demonstrated that the low-cost conductive coating can be used to actively alter the stiffness of the structure through surface joule heating. The process was found to result in repeatable and reproduceable stiffness tuning. Stiffness reductions of 56% and 94% were demonstrated for single and dual material configurations under the same electrical loading. The proposed methodology can be implemented to actively control the properties of polymeric lattice materials/structures where the change in the composition of polymers (introduce bulk electrical conductivity) is difficult and can have a wide range of applications in soft robotics, shape-changing, and deployable structures.
Micheal Sakr and Ayan Sadhu 2024 Smart Mater. Struct. 33 033001
Digital twins (DTs) have witnessed a paramount increase in applications in multidisciplinary engineering systems. With advancements in structural health monitoring (SHM) methods and implementations, DT-based maintenance and operation stages have been implemented significantly during the life cycle of civil infrastructure. Recent literature has started laying the building blocks for incorporating the concept of DTs with SHM of large-scale civil infrastructure. This paper undertakes a systematic literature review of studies on DT-related applications for SHM of civil structures. It classifies the articles based on thematic case studies: transportation infrastructure (i.e. bridges, tunnels, roads, and pavements), buildings, off-shore marine infrastructure and wind turbines, and other civil engineering systems. The proposed review is further uniquely sub-classified using diverse modeling approaches such as building information modeling, finite element modeling, 3D representation, and surrogate and hybrid modeling used in DT implementations. This paper is solely focused on applications relating DTs to SHM practices for various civil engineering infrastructures, hence highlighting its novelty over previous reviews. Gaps and limitations emerging from the systematic review are presented, followed by articulating future research directions and key conclusions.
Xianxu 'Frank' Bai et al 2024 Smart Mater. Struct. 33 033002
In the last two decades, magnetorheological (MR) fluids have attracted extensive attention since they can rapidly and continuously control their rheological characteristics by adjusting an external magnetic field. Because of this feature, MR fluids have been applied to various engineering systems. This paper specifically investigates the application of MR fluids in shock mitigation control systems from the aspects of three key technical components: the basic structural design of MR fluid-based energy absorbers (MREAs), the analytical and dynamical model of MREAs, and the control method of adaptive MR shock mitigation control systems. The current status of MR technology in shock mitigation control is presented and analyzed. Firstly, the fundamental mechanical analysis of MREAs is carried out, followed by the introduction of typical MREA configurations. Based on mechanical analysis of MREAs, the structural optimization of MREAs used in shock mitigation control is discussed. The optimization methods are given from perspectives of the design of piston structures, the layout of electromagnetic coil, and the MR fluid gap. Secondly, the methods of damper modeling for MREAs are presented with and without consideration of the inertia effect. Then both the modeling methods and their characteristics are introduced for representative parametric dynamic models, semi-empirical dynamic models, and non-parametric dynamic models. Finally, the control objectives and requirements of the shock mitigation control systems are analyzed, and the current competitive methods for the ideal 'soft-landing' control objectives are reviewed. The typical control methods of MR shock mitigation control systems are discussed, and based on this the evaluation indicators of the control performance are summarized.
P Narayanan et al 2024 Smart Mater. Struct. 33 043001
Hard-magnetic soft materials (hMSMs) are smart composites that consist of a mechanically soft polymer matrix impregnated with mechanically hard magnetic filler particles. This dual-phase composition renders them with exceptional magneto-mechanical properties that allow them to undergo large reversible deformations under the influence of external magnetic fields. Over the last decade, hMSMs have found extensive applications in soft robotics, adaptive structures, and biomedical devices. However, despite their widespread utility, they pose considerable challenges in fabrication and magneto-mechanical characterization owing to their multi-phase nature, miniature length scales, and nonlinear material behavior. Although noteworthy attempts have been made to understand their coupled nature, the rudimentary concepts of inter-phase interactions that give rise to their mechanical nonlinearity remain insufficiently understood, and this impedes their further advancements. This holistic review addresses these standalone concepts and bridges the gaps by providing a thorough examination of their myriad fabrication techniques, applications, and experimental, and modeling approaches. Specifically, the review presents a wide spectrum of fabrication techniques, ranging from traditional molding to cutting-edge four-dimensional printing, and their unbounded prospects in diverse fields of research. The review covers various modeling approaches, including continuum mechanical frameworks encompassing phenomenological and homogenization models, as well as microstructural models. Additionally, it addresses emerging techniques like machine learning-based modeling in the context of hMSMs. Finally, the expansive landscape of these promising material systems is provided for a better understanding and prospective research.
Amanda White et al 2024 Smart Mater. Struct. 33 055053
Inflatable structures, promising for future deep space exploration missions, are vulnerable to damage from micrometeoroid and orbital debris impacts. Polyvinylidene fluoride-trifluoroethylene (PVDF-trFE) is a flexible, biocompatible, and chemical-resistant material capable of detecting impact forces due to its piezoelectric properties. This study used a state-of-the-art material extrusion system that has been validated for in-space manufacturing, to facilitate fast-prototyping of consistent and uniform PVDF-trFE films. By systematically investigating ink synthesis, printer settings, and post-processing conditions, this research established a comprehensive understanding of the process-structure-property relationship of printed PVDF-trFE. Consequently, this study consistently achieved the printing of PVDF-trFE films with a thickness of around 40 µm, accompanied by an impressive piezoelectric coefficient of up to 25 pC N−1. Additionally, an all-printed dynamic force sensor, featuring a sensitivity of 1.18 V N−1, was produced by mix printing commercial electrically-conductive silver inks with the customized PVDF-trFE inks. This pioneering on-demand fabrication technique for PVDF-trFE films empowers future astronauts to design and manufacture piezoelectric sensors while in space, thereby significantly enhancing the affordability and sustainability of deep space exploration missions.
M A H Khondoker and D Sameoto 2016 Smart Mater. Struct. 25 093001
This review contains a comparative study of reported fabrication techniques of gallium based liquid metal alloys embedded in elastomers such as polydimethylsiloxane or other rubbers as well as the primary challenges associated with their use. The eutectic gallium–indium binary alloy (EGaIn) and gallium–indium–tin ternary alloy (galinstan) are the most common non-toxic liquid metals in use today. Due to their deformability, non-toxicity and superior electrical conductivity, these alloys have become very popular among researchers for flexible and reconfigurable electronics applications. All the available manufacturing techniques have been grouped into four major classes. Among them, casting by needle injection is the most widely used technique as it is capable of producing features as small as 150 nm width by high-pressure infiltration. One particular fabrication challenge with gallium based liquid metals is that an oxide skin is rapidly formed on the entire exposed surface. This oxide skin increases wettability on many surfaces, which is excellent for keeping patterned metal in position, but is a drawback in applications like reconfigurable circuits, where the position of liquid metal needs to be altered and controlled accurately. The major challenges involved in many applications of liquid metal alloys have also been discussed thoroughly in this article.
Open all abstracts, in this tab
Ling Zheng et al 2024 Smart Mater. Struct. 33 065026
Actuators are pivotal for empowering robots to execute a wide array of tasks and adapt to diverse surroundings. However, conventional actuators with a low switching frequency and a prolonged response time significantly comprise the adaptability of robots, restricting them to single operation conditions. This paper presents a solution to this issue by introducing a dexterous actuator integrated with magnetorheological bearings (referred to as MR actuator) for real-time controllable damping. Compared to conventional actuators, the MR actuator boasts exceptional dexterity, featuring a significantly-elevated switching frequency and swifter response time. To validate the remarkable dexterity of this MR actuator, rapid commutation tests and transient response experiments were conducted. Impressively, the MR actuator achieved a stable switching frequency of up to 10 Hz, surpassing that of conventional actuators (2 Hz). Moreover, it demonstrated a reduced response time and a heightened energy efficiency. Beyond robotics, applications of MR actuators are also found in areas requiring an improved machinery precision and production efficiency.
Xiaotian Zheng et al 2024 Smart Mater. Struct. 33 065027
In this paper, a piezoelectric breeze energy harvester with a mechanical intelligence mechanism for smart agricultural monitoring systems (G-PBEH) is proposed. Different from the conventional magnetically coupled piezoelectric cantilever beam harvesters where the end magnet is mostly fixed, the G-PBEH has movable magnets in a fixed cylindrical channel. Which could achieve a mechanical intelligence mechanism with the tuned magnets on the shell, contributing to increasing voltage frequency and widening wind bandwidth. The effects of cylindrical channel length (L) and tuned magnet diameter (D) on performance were investigated. The experimental findings reveal that when L is 10 mm and D is 8 mm, the prototype starts at 2 m s−1, and the highest voltage and power are 17.9 V and 944.07 μW (150 kΩ) at 8 m s−1 . Compared to L is 5 mm (magnet fixed), the voltage waveform has a 28.6% increase in the quantity of peaks. Besides, the voltage is larger than 3 V occupying 91.6% of the experimental wind bandwidth. The application experiment demonstrates that the G-PBEH can be used as a reliable power supplier, which can facilitate the progress of smart monitoring systems for simplified greenhouses in remote areas.
Amirreza Torabizadeh et al 2024 Smart Mater. Struct. 33 065025
This study proposes a novel triangular added damping and stiffness (TADAS) damper that uses the shape memory effect of iron-based shape memory alloy (Fe-SMA) to provide a self-centering system to recover the initial shape of a structure after significant inelastic deformation induced by nonlinear response of fused elements, without the need for difficult and expensive replacement procedures of conventional TADAS systems. Unlike most studies which consider simplified uniaxial behavior of Fe-SMAs, the present non-linear finite element simulations cover the full 3D material non-linearity of Fe-SMA component based on the SMA constitutive law to capture both flexural and shear behavior in various coupled thermomechanical loadings, including the mechanical loading/unloading, the heating, and the final cooling (as the recovering process). Simulations performed on a one-bay steel frame for different drift ratios reveal that although the dissipation energy of the new device is at most 10% less than the ordinary one, it enjoys the self-centering property to recover the initial shape of the frame before loading, showing that the proposed damper is an effective alternative to ordinary TADAS yielding dampers to achieve the self-centering characteristics.
Xiaoyuan Wang et al 2024 Smart Mater. Struct. 33 065024
The functional fatigue behavior of shape memory alloy (SMA) beam actuators is gaining importance as their utilization in engineering applications becomes more widespread. However, research on the functional fatigue behavior of SMA beam actuators under bending conditions is not as extensive as that on SMA wires. In this paper, an experimental study and theoretical analysis of the functional fatigue behavior of SMA beam actuators were conducted. A measuring method for bending deflection and an automatic thermal cyclic test bench was designed. A series of functional fatigue tests were conducted on SMA beam actuators under different bias load conditions and the functional fatigue patterns were obtained. The material damage factor is defined and calculated through specimen tests. By incorporating the damage factor to modify the existing constitutive model, a model considering functional fatigue and tension-compression asymmetry is obtained. Finite element analysis (FEA) is performed based on this modified model to simulate the actuating performance of SMA beam actuators and to compute the deflection at different numbers of cycles. Additionally, a small parameter study on the actuator shape is conducted using FEA. By comparing the FEA results with functional fatigue experimental data, the effectiveness of the modified model is validated, demonstrating its capability to describe functional fatigue and predict actuator lifespan.
Shengyao Jia et al 2024 Smart Mater. Struct. 33 065023
The energy crisis and environmental pollution have driven the development of ambient energy harvesting technologies, and ocean waves usually contain abundant vibration energy, making the study of wave energy harvesting technology of profound value. This paper proposes a hybrid wave vibration energy harvester with electromagnetic double-speed and piezoelectric up-frequency driven by a rotating ball. For the electromagnetic generator (EMG), the excitation magnet and coil move simultaneously, resulting in double the flux variation rate compared with traditional structures, enhancing the output voltage. For the piezoelectric transducer (PZT), four piezoelectric cantilever beams are magnetically coupled with the EMG, generating power through bistable motion and broadening the working frequency band of the cantilever beam structure. The harvester is modeled and simulated, and its performance is tested on a simulated vibration platform, with simulation and experimental results in good agreement. Under external excitation at 0.8 Hz, the optimal load and maximum power for each EMG are 8.2 Ω and 207.2 mW, respectively, and the optimal load and maximum power for each PZT are 100 kΩ and 1.52 mW, respectively. The harvester can produce a maximum output power of 420.48 mW, demonstrating high efficiency in energy capture under low-frequency and multidirectional wave excitation.
Open all abstracts, in this tab
Bouguermouh Karima et al 2024 Smart Mater. Struct. 33 063001
Four-dimensional (4D) printing has recently received much attention in the field of smart materials. It concerns using additive manufacturing to obtain geometries that can change shape under the effect of different stimuli. Such a technique enables the fabrication of 3D printed parts with the additional functionality of scalable, programmable, and controllable part shapes over time. This review provides a comprehensive examination of advances in the field of 4D printing, emphasizing the integration of fiber reinforcement and auxetic structures as crucial building blocks. The incorporation of fibers enhances structural integrity, while auxetic design principles contribute unique mechanical properties, such as negative Poisson's ratio and great potential for energy absorption due to their specific deformation mechanisms. Therefore, they present potential applications in aerospace, drones, and robotics. The objective of this review article is first to describe the distinctive properties of shape memory polymers, auxetic structures, and composite (fiber-reinforced) materials. A review of applications that use combinations of such materials is also presented when appropriate. The goal is to get a grip on the delicate balance between the different properties achievable in each case. The paper concludes by describing recent advances in 4D printing of fiber-reinforced auxetic structures.
Xuan Phu Do and Seung Bok Choi 2024 Smart Mater. Struct. 33 053001
In this review article, different structural types of the magnetic core required for activation of magnetorheological elastomer (MRE) and magnetorheological fluid (MRF) are introduced in terms of design feature, magnetic flux analysis and performance, installation with primary structure and close relationship to material types. As a first step, dynamic functions related to the chosen models are summarized and discussed according to the magnetic field variations including the field-dependent damping force and torque of the application systems. To address on the practical feasibility, main issues of design process are also pointed out and are discussed stating the manufacturing feasibility and the scaled factors of dynamic variables. Then, after analysing the featured models and dynamic functions, the derivation approaches to establish mathematical models of the magnetic circuit core (MCC) are provided and compared as a valuable reference for checking both simplicity and accuracy. In this stage, the chosen symbolized magnetic circuit models are clearly described about linear or/and nonlinear behaviours of the input (current) and output (magnetic field). In addition, a couple of commercial software to design the magnetic circuit model is introduced since they can be effectively adopted to analyse the MCCs of many application systems utilizing MRE and MRF without any difficulty.
Ravindra Masana et al 2024 Smart Mater. Struct. 33 043002
Structures inspired by the Kresling origami pattern have recently emerged as a foundation for building functional engineering systems with versatile characteristics that target niche applications spanning different technological fields. Their light weight, deployability, modularity, and customizability are a few of the key characteristics that continue to drive their implementation in robotics, aerospace structures, metamaterial and sensor design, switching, actuation, energy harvesting and absorption, and wireless communications, among many other examples. This work aims to perform a systematic review of the literature to assess the potential of the Kresling origami springs as a structural component for engineering design keeping three objectives in mind: (i) facilitating future research by summarizing and categorizing the current literature, (ii) identifying the current shortcomings and voids, and (iii) proposing directions for future research to fill those voids.
P Narayanan et al 2024 Smart Mater. Struct. 33 043001
Hard-magnetic soft materials (hMSMs) are smart composites that consist of a mechanically soft polymer matrix impregnated with mechanically hard magnetic filler particles. This dual-phase composition renders them with exceptional magneto-mechanical properties that allow them to undergo large reversible deformations under the influence of external magnetic fields. Over the last decade, hMSMs have found extensive applications in soft robotics, adaptive structures, and biomedical devices. However, despite their widespread utility, they pose considerable challenges in fabrication and magneto-mechanical characterization owing to their multi-phase nature, miniature length scales, and nonlinear material behavior. Although noteworthy attempts have been made to understand their coupled nature, the rudimentary concepts of inter-phase interactions that give rise to their mechanical nonlinearity remain insufficiently understood, and this impedes their further advancements. This holistic review addresses these standalone concepts and bridges the gaps by providing a thorough examination of their myriad fabrication techniques, applications, and experimental, and modeling approaches. Specifically, the review presents a wide spectrum of fabrication techniques, ranging from traditional molding to cutting-edge four-dimensional printing, and their unbounded prospects in diverse fields of research. The review covers various modeling approaches, including continuum mechanical frameworks encompassing phenomenological and homogenization models, as well as microstructural models. Additionally, it addresses emerging techniques like machine learning-based modeling in the context of hMSMs. Finally, the expansive landscape of these promising material systems is provided for a better understanding and prospective research.
Xianxu 'Frank' Bai et al 2024 Smart Mater. Struct. 33 033002
In the last two decades, magnetorheological (MR) fluids have attracted extensive attention since they can rapidly and continuously control their rheological characteristics by adjusting an external magnetic field. Because of this feature, MR fluids have been applied to various engineering systems. This paper specifically investigates the application of MR fluids in shock mitigation control systems from the aspects of three key technical components: the basic structural design of MR fluid-based energy absorbers (MREAs), the analytical and dynamical model of MREAs, and the control method of adaptive MR shock mitigation control systems. The current status of MR technology in shock mitigation control is presented and analyzed. Firstly, the fundamental mechanical analysis of MREAs is carried out, followed by the introduction of typical MREA configurations. Based on mechanical analysis of MREAs, the structural optimization of MREAs used in shock mitigation control is discussed. The optimization methods are given from perspectives of the design of piston structures, the layout of electromagnetic coil, and the MR fluid gap. Secondly, the methods of damper modeling for MREAs are presented with and without consideration of the inertia effect. Then both the modeling methods and their characteristics are introduced for representative parametric dynamic models, semi-empirical dynamic models, and non-parametric dynamic models. Finally, the control objectives and requirements of the shock mitigation control systems are analyzed, and the current competitive methods for the ideal 'soft-landing' control objectives are reviewed. The typical control methods of MR shock mitigation control systems are discussed, and based on this the evaluation indicators of the control performance are summarized.
Open all abstracts, in this tab
Gu et al
The traditional rebar binding devices require complex drive and transmission mechanisms, which leads to large volume and complex structure. In this paper, a cylindrical thermoplastic shape memory polymer (SMP) fixture is proposed to verify the rebar binding method of thermal-mechanism coordination. The SMP fixture is manufactured by the injection molding technology through selecting suitable-ratio Polylactic acid (PLA) and Polycaprolactone (PCL) blend materials. Besides, an additional auxiliary device is presented to overcome the incomplete recovery disadvantage existing in the thermoplastic SMP and completely achieve binding the rebar. On this base, two different binding methods are proposed to compare the mechanical performance after fixing the rebar, and the external force/thermal contributions are tested and discussed in detail. The tested results show that the binding contribution of heat could reach 70% while the binding contribution of external force could reach 30% above the transition temperature (Tg). The maximum tensile force that the binding rebar can withstand under the thermal-mechanism coordination action could reach up to 657.7 N, which is higher than the maximum tensile force of the wire binding. In addition, the maximum friction force between rebar and notches of fixture could reach up to 94.1 N, which further verifies the feasibility of thermal-mechanism coordination for binding reinforcing mesh based on SMP fixture.
Demo et al
In recent years, there has been growing interest in self-sensing structural materials across research and industry sectors. Detecting and locating structural damage typically requires numerous sensors wired to a data acquisition (DAQ) circuit, rendering implementation impractical in real structures. This paper proposes an innovative, cost-effective sensor network for damage detection and localization in fiber-reinforced polymer composites. The innovation encompasses three key elements: (1) utilizing carbon fiber tows within the composite as piezoresistive sensors, eliminating the need for additional foreign sensor devices; (2) introducing a novel sensor layout wherein sensor tow branches with varied resistance values are connected in parallel, reducing the number of connections to the DAQ circuit and cutting manufacturing costs significantly; (3) developing a practical sensor terminal fabrication technique to minimize manufacturing expenses. The proposed design methodology for the branch resistance values is first validated using a demonstration panel. Subsequently, the overall strategy is assessed by conducting impact tests on carbon and glass fiber-reinforced composite specimens. Results validate the sensor's ability to accurately detect and locate structural damage.
Weng et al
This study proposes a rectangular microstrip patch antenna sensor based on a high-conductivity graphene film for bidirectional strain detection in structural health monitoring (SHM). By using a highly conductive graphene film instead of traditional metal foil to produce a patch antenna, the antenna possesses a higher flexibility and a larger sensing range. The mechanical, electromagnetic, and radiative properties were investigated. The strain sensing principle based on the resonant frequency offset of the graphene film antenna was proposed. The relationships between the resonant frequency shift and structural strain were quantitatively explored through theoretical deductions, finite element simulations, and experiments. According to the experimental results, the shift in the resonant frequency was linearly related to the lateral and longitudinal strains. The sensitivity coefficients for the lateral and longitudinal strains were 2.2037 kHz/με and 3.6198 kHz/με, respectively. The thermal strain can be distinguished based on the linear resonant frequency-temperature relationship. The results demonstrated the advantages and prospects of the proposed novel patch antenna for SHM.
Jin et al
This paper addresses the modeling of dynamic hysteresis and creep in piezoelectric actuators, and employs feedforward open-loop control based on inverse models to compensate for hysteresis and creep phenomena. The comprehensive model consists of quasi dynamic and-dynamic components. The quasi-dynamic model combines the quasi-dynamic Prandtl-Ishlinskii model with an Prandtl-Ishlinskii-based linear time-invariant model, while the dynamic part utilizes the auto-regressive exogenous model. The model accurately describes creep and dynamic hysteresis with modeling errors of less than 0.01 μm and 0.14 μm, respectively. The inversion of the comprehensive model has been proven to exhibit unique convergence. Under inverse feedforward control, the improvement in dynamic hysteresis and hysteresis with creep can be achieved at 94% and 83%, respectively. The comprehensive model proposed in this paper accurately describes the dynamic hysteresis and creep phenomena in piezoelectric actuators and realizes open-loop compensation control, achieving precise actuation of piezoelectric actuators.
Di Brizzi et al
Auxetics are a class of materials and metamaterials with a negative Poisson's ratio (ν) and have gained tremendous popularity over the last three decades. Many studies have focused on characterizing designs that allow obtaining a negative ν. However, some open issues remain concerning understanding the auxetic behavior in operational conditions. Studies have been centered on analyzing the response of specific auxetic topologies instead of treating auxeticity as a property to be analyzed in a well-defined structural context. This study aims to contribute to the investigation of auxetic materials with a structural application, focusing on maximizing performance. The field of application of auxetics for designing inserts was selected and a model of a nail-cavity system was created to determine the effects of different design choices on the system behavior by exploring relationships between selected parameters and the auxetic insert behavior. The exploration combines finite element modeling analyses with their surrogate models generated by supervised learning algorithms. This approach allows for exploring the system's behavior in detail, thus demonstrating the potential effectiveness of auxetics when used for such applications. A list of design guidelines is elaborated to support the exploitation of auxetics in nail-cavity systems.
Trending on Altmetric
Open all abstracts, in this tab
Luke Benjamin Demo et al 2024 Smart Mater. Struct.
In recent years, there has been growing interest in self-sensing structural materials across research and industry sectors. Detecting and locating structural damage typically requires numerous sensors wired to a data acquisition (DAQ) circuit, rendering implementation impractical in real structures. This paper proposes an innovative, cost-effective sensor network for damage detection and localization in fiber-reinforced polymer composites. The innovation encompasses three key elements: (1) utilizing carbon fiber tows within the composite as piezoresistive sensors, eliminating the need for additional foreign sensor devices; (2) introducing a novel sensor layout wherein sensor tow branches with varied resistance values are connected in parallel, reducing the number of connections to the DAQ circuit and cutting manufacturing costs significantly; (3) developing a practical sensor terminal fabrication technique to minimize manufacturing expenses. The proposed design methodology for the branch resistance values is first validated using a demonstration panel. Subsequently, the overall strategy is assessed by conducting impact tests on carbon and glass fiber-reinforced composite specimens. Results validate the sensor's ability to accurately detect and locate structural damage.
Diego Di Brizzi et al 2024 Smart Mater. Struct.
Auxetics are a class of materials and metamaterials with a negative Poisson's ratio (ν) and have gained tremendous popularity over the last three decades. Many studies have focused on characterizing designs that allow obtaining a negative ν. However, some open issues remain concerning understanding the auxetic behavior in operational conditions. Studies have been centered on analyzing the response of specific auxetic topologies instead of treating auxeticity as a property to be analyzed in a well-defined structural context. This study aims to contribute to the investigation of auxetic materials with a structural application, focusing on maximizing performance. The field of application of auxetics for designing inserts was selected and a model of a nail-cavity system was created to determine the effects of different design choices on the system behavior by exploring relationships between selected parameters and the auxetic insert behavior. The exploration combines finite element modeling analyses with their surrogate models generated by supervised learning algorithms. This approach allows for exploring the system's behavior in detail, thus demonstrating the potential effectiveness of auxetics when used for such applications. A list of design guidelines is elaborated to support the exploitation of auxetics in nail-cavity systems.
Huanpeng Hong et al 2024 Smart Mater. Struct.
Iron-based shape memory alloys (FeSMA) are emerging as promising materials for use in post-tensioning concrete structures to provide self-centering capabilities during a seismic event. Past experimental studies on FeSMA focused on strengthening or repairing existing structural components. In addition to the structural rehabilitation for gravity loading, FeSMA also have potential for use in self-centering columns subjected to seismic loads. However, the basic material properties, such as strength, ductility, recovery strain, actuation stress (i.e., prestress) stability, low-cycle fatigue resistance, and temperature dependence of FeSMA related to self-centering column applications have not been studied so far. To fill this knowledge gap and determine the feasibility of using FeSMA in self-centering columns, this study performed a comprehensive characterization and analysis of FeSMA both before and after actuation (i.e., thermal stimulation). The strength, ductility, and recovery strain of FeSMA before actuation were tested at different temperatures from -40℃ to 50℃. After actuation, the actuation stress, low-cycle fatigue resistance, and strain capacity of FeSMA were tested at different temperatures from -40℃ to 50℃, prestrain levels from 4% to 30%, and under low-cycle fatigue loading with strain amplitudes from 0.5% to 1.0%. The results from this study demonstrated that FeSMA exhibit high ductility, cyclic actuation stress stability, and low-cycle fatigue resistance at temperatures from -40℃ to 50℃. Furthermore, it was found that increasing the prestrain level can effectively increase the post-actuation strain amplitude at which the actuation stress reduces to zero. A prestrain level between 15% and 20% is recommended for application of FeSMA in self-centering columns. The research findings from this study demonstrated the feasibility of using FeSMA in self-centering columns subject to seismic loading.
Joshua Knospler et al 2024 Smart Mater. Struct.
Soft robots have revolutionized machine interactions with humans and the environment to enable safe operations. The fixed morphology of these soft robots dictates their mechanical performance, including strength and stiffness, which limits their task range and applications. Proposed here are modular, reconfigurable soft robots with the capabilities of changing their morphology and adjusting their stiffness to perform versatile object handling and planar or spatial operational tasks. The reconfiguration and tunable interconnectivity between the elemental soft, pneumatically driven actuation units is made possible through integrated permanent magnets with coils (PMC). The proposed concept of attaching/detaching actuators enables these robots to be easily rearranged in various configurations to change the morphology of the system. While the potential for these actuators allows for arbitrary reconfiguration through parallel or serial connection on their four sides, we demonstrate here a configuration called ManusBot. ManusBot is a hand-like structure with digits and palm capable of individual actuation. The capabilities of this system are demonstrated through specific examples of stiffness modulation, variable payload capacity, and structure forming for enhanced and versatile object manipulation and operations. The proposed modular, soft robotic system with interconnecting capabilities significantly expands the versatility of operational tasks as well as the adaptability of handling objects of various shapes, sizes, and weights using a single system.
Pedro M. Ferreira et al 2024 Smart Mater. Struct.
In the field of structural engineering, the integration of smart materials and structural health monitoring (SHM) has given rise to self-sensing materials (SSM), leading to a paradigm shift in SHM. This paper focuses on the interplay between self-sensing capabilities and the piezoelectric properties of lead zirconate titanate (PZT) and barium titanate (BT) in aluminium components. Leveraging Friction Stir Processing (FSP), the study explores the synthesis and performance of self-sensing materials with embedded piezoelectric particles, potentially transforming structural engineering. The paper highlights FSP as a key methodology for incorporating piezoelectric particles into structural materials, showcasing its potential in developing self-sensing materials with enhanced functionalities. A specific focus is placed on integrating PZT and BT particles into AA2017-T451 aluminium parts using FSP, with metallographic assessments and mechanical property evaluations conducted to analyse particle distribution and concentration. This study shows how BT and PZT particles are incorporated into AA2017-T451 aluminium to create a self-sensing material that responds to external stimuli. Under cyclic loading, the self-sensing materials exhibit a linear load-electrical response correlation, with sensibility increasing at lower frequencies. Metallographic analysis shows homogeneous particle distribution, while PZT induces increased brittleness and brittle fractures. Yield strength remains relatively stable, but ultimate strength decreases post-FSP. Hardness variations indicate weaker bonding with PZT particles. Eddy's current testing aligns with hardness profiles, and sensorial characterization reveals a non-linear frequency-sensibility relationship, showcasing the SSMs' suitability for low-frequency applications, particularly with PZT embedment.
Mahdi Alaei Varnosfaderani et al 2024 Smart Mater. Struct. 33 065019
Inspired by the bending vibration observed in the biological locomotions such as those found in snakes, horned lizards, and sandfish, we have developed a novel vibro probe utilizing bending resonance modes to study the bending vibration effects in assisting penetration into granular materials. This approach contrasts with traditional probes that rely on longitudinal vibrations for penetration. This newly developed probe was used to experimentally investigate the impact of bending vibration in reducing the required penetration force and enhancing the penetration process within granular materials such as lunar or Martian regolith. The bending vibrations were excited by thin piezo patches attached to the probe's machined surface without increasing the probe's outside diameter. This simple mechanism enables pushing the whole probe inside the granular materials. Experimental modal analysis was employed to determine the resonance frequencies of the probe. Subsequently, the probe was pushed into granular materials, both with and without the bending vibrations, by a linear actuator. Experimental results indicated that employing bending vibration in one direction led to a reduction in penetration force by up to 27% while utilizing two directions resulted in a reduction of up to 42%. Additionally, when the probe stopped penetrating the soil due to insufficient axial force, bi-directional bending vibration proved more effective in swiftly fluidizing the surrounding soil. These findings highlight the efficacy of bending vibrations in compact subsurface drilling tools.
Seiki Chiba et al 2024 Smart Mater. Struct. 33 065016
Actuators, sensors, and generators using dielectric elastomers (DEs) are inexpensive and light, and can be easily to structured, multilayer-able, and very efficient. They are ideal for an eco-energy society. In the latest technology, an only 0.15 g DE can lift an 8 kg weight by 1 mm or more in just 88 ms. The near future, it can be applied to efficient drive systems of humanoid robots, systems that assist in driving the motors of electric vehicles, and various industrial machinery. It is highly likely that very thin and miniaturized DE sensors would also support the driving of motors. In addition, DE generators, which can be applied to various external forces, have attracted significant attention as a renewable energy source. In this paper, we discuss the R&D status of DEs using mainly commercially available elastomer materials, give examples of issues, and discuss and their potential applications, and usefulness. The excellent performance of the DEs mentioned above is largely due to their carbon-based electrodes. In this study, various carbon materials (including carbon grease, carbon black, MWCNT, and SWCNT) and their DE performances were compared.
Elinor Barnett et al 2024 Smart Mater. Struct. 33 065010
Despite bone screws being the most commonly inserted implant in orthopaedic surgery, 10% of fracture fixation failure is a result of screw migration or pullout. In this study, the effect of four auxetic structures on the pullout performance of a novel unthreaded bone fastener was investigated through experiments and numerical simulations. The auxetic fasteners included the re-entrant, rotating squares, missing rib, and tetrachiral structures. Parametric CAD models were developed for each, and polymer samples manufactured using a stereolithography process. Pullout testing using bone analogue material found the rotating squares fastener to achieve superior pullout resistance 2.5 times that of the non-auxetic control sample. With a pullout to push-in force ratio of 33.7, this fastener achieved high pullout resistance with a low insertion force improving ease of installation. The Poisson's ratio of the structure was determined using image analysis to be −1.31, similar to the missing rib and re-entrant types. The low axial stiffness of 12.1 N mm−1 for the rotating squares fastener was the reason for superior performance, allowing axial and resulting transverse strain to be initiated at relatively low load. The effect of increased diametral interference was investigated, and the re-entrant structure found to be superior with pullout resistance improved by 342%. This work provides a foundation for further development of unthreaded auxetic bone fasteners, which have the potential to replace screws for some orthopaedic applications and significantly reduce the prevalence of pullout as a failure mode.
Akshayveer et al 2024 Smart Mater. Struct. 33 065009
In recent times, there have been notable advancements in haptic technology, particularly in screens found on mobile phones, laptops, light-emitting diode (LED) screens, and control panels. However, it is essential to note that the progress in high-temperature haptic applications is still in the developmental phase. Due to their complex phase and domain structures, lead-free piezoelectric materials such as (BNT)-based haptic technology behave differently at high temperatures than in ambient conditions. Therefore, it is essential to investigate the aspects of thermal management and thermal stability, as temperature plays a vital role in the phase and domain transition of BNT material. A two-dimensional thermo-electromechanical model has been proposed in this study to analyze the thermal stability of the BNT-PDMS composite by analyzing the impact of temperature on effective electromechanical properties and mechanical and electric field parameters. However, the thermo-electromechanical modelling of the BNT-PDMS composite examines the macroscopic effects of the applied thermal field on mechanical and electric field parameters, as phase change and microdomain dynamics are not considered in this model. This study analyzes the impact of thermo-electromechanical coupling on the performance of the BNT-PDMS composite compared to conventional electromechanical coupling. The results predicted a significant improvement in piezoelectric response compared to electromechanical coupling due to the increased thermoelectric effect in the absence of phase change and microdomain switching for temperature boundary conditions below depolarization temperature (C for pure BNT material).
Iman Valizadeh and Oliver Weeger 2024 Smart Mater. Struct. 33 065006
A major benefit of additive manufacturing technologies is precise control over structural topologies and material properties, which allows to tailor, for instance, energy absorption and dissipation. While vat photopolymerization is generally restricted to a single material, grayscale masked stereolithography (gMSLA) allows to customize material behavior by grading the light intensity within a structure. This study investigates the impact and opportunities of grayscale grading strategies on the rate-dependent mechanical behavior of structures fabricated by gMSLA. Considering the viscoelastic nature of polymers, rate-dependent energy dissipation is explored, introducing a parametric linear viscoelastic constitutive model for varying grayscales. The investigation includes the comprehensive characterization of mechanical properties, numerical finite element simulation, validation through experimental procedures, and exploration of dissipation energy under different strain rates. In this way, a rational function successfully determines the critical strain rate at which the maximum dissipation occurs. Overall, the research offers a comprehensive investigation of the mechanical dissipation behavior of graded 3D printed structures, laying the foundation for further studies and advancements aimed at optimizing these structures for enhanced energy absorption capabilities.